Removable Concrete Anchor with Sleeve, 20 mm Hole
Code: AFA930310
EN 795:2012 Type AANSI Z359.1-2007AS/NZS 5532:2013
A removable chemical fastener anchor for concrete structures with a minimum thickness of 150mm, installed through a pre-defined hole of 20.0 mm diameter. A lock prevents the anchorage eye from coming out of the stud accidentally.
Prices are sent in a quotation once you submit your cart, adjusted to your quantity and delivery location.
Key features
- Lock prevents the anchorage eye from coming out of the stud accidentally
- For concrete with a minimum thickness of 150mm
- Installed through a pre-defined hole of 20.0 mm diameter
Technical specifications
| Material | Fully Threaded Stud: Stainless Steel; Anchorage Eye: Alloy Steel |
|---|---|
| Breaking strength | 15 kN |
| Finish | Fully threaded stud: Polished; Anchorage Eye: Shot blasted |
| Minimum concrete thickness | 150mm |
| Installation hole | 20.0 mm diameter |
| Weight | 346.0 gm ± 10.0 gm |
| Standards | EN 795:2012 Type A, ANSI Z359.1-2007, AS/NZS 5532:2013 |
BUYER'S GUIDE
Selecting a Safe Anchorage Point
The anchorage is the A in the ABCD of fall protection: the point on an independent structure that secures the fall protection device or lanyard. Anchor devices are classified under EN 795:2012 as Type A to E, and every anchor must be strong enough to hold a user in a fall.
- A single anchor point should be rated to at least 12kN for one person; for two people on one anchor the minimum is 21 kN, and no more than two people may use a single anchor.
- Attach at or above shoulder level and as directly overhead as possible, because a low or side anchor increases the fall distance and can cause a pendulum swing into obstacles.
- If unsure of the load rating, consult an engineer; good anchorages are I-beams and other solid fixtures, and you should never anchor to cable hangers, light fixtures or anything not designed for a sudden heavy load.
- Make sure the anchor is approved by the employer or an engineer and check it for damage before connecting; tag out a damaged anchor until a competent person has inspected it.
- Only authorised personnel may install and certify roofing anchors.
Summarised from the manufacturer's catalogue. Selection must follow your site risk assessment and the competent person's judgement.
Compare similar products
| Product | Standards | Weight | Length | |
|---|---|---|---|---|
| Removable Concrete Anchor with Sleeve, 20 mm Hole AFA930310 |
EN 795:2012 Type A, ANSI Z359.1-2007, AS/NZS 5532:2013 | 346.0 gm ± 10.0 gm | — | This product |
| Removable Concrete Anchor, 18-19 mm Hole AFA930301 |
EN 795:2012 Type B, AS/NZS 5532:2013 | 150.0 gm ± 10 gm | — | View |
| Edge Stainless Steel M12 Concrete Anchor Point 15 kN AFA935515 |
ANSI Z359.18-2017 Type A, AS/NZS 5532:2013 | 299.3 gms ± 10.0 gms | — | View |
| Edge Stainless Steel M16 Concrete Anchor Point AFA935508 |
EN 795:2012 Type A, AS/NZS 5532:2013 | 330.0 gms ± 10.0 gms | — | View |
| Concrete Anchor with D-Ring, M16 (Chemical Anchor Bolt Not Supplied) AFA930316C |
EN 795:2012 Type A, ANSI Z359.1-2007, AS/NZS 5532:2013 | 280.0 gms ± 20.0 gms | — | View |
More in this family
Technical data from the manufacturer's catalogue, page 115. Specifications may change; please confirm with our team before ordering.
